Creek OBH-21SE Headphone Pre Amp

296.17

Be the first to review this product

Availability: Available

£296.17
OR

Quick Overview

The Creek OBH- 21SE headphone amplifiers eliminate the need to use a full sized integrated amplifier to boost the audio signal when only headphones are used. An average output level CD player or tuner can be connected directly to the input of the headphone amplifier.

Creek-Headphone-Pre-Amp-OBH- 21SE

  • Creek-Headphone-Pre-Amp-OBH- 21SE

The OBH-21SE incorporates advanced circuitry utilising high grade op-amps for signal amplification, providing the capability to drive headphones with impedances ranging from 30 to 300 Ohms without a problem. Gain (level) will be greater for lower impedance headphones.

There are two 1/4" (6.3mm) stereo headphone jacks on the front panel. The matching impedance for each of these sockets is slightly different which allows for better individual matching. When using two sets of headphones, the impedance will be the same for both. The output level can be adjusted by a high-grade ALPS Blue Velvet 27mm volume potentiometer coupled to a solid metal control knob on the front panel. The OBH-21SE has one pair of stereo inputs using stereo RCA (Phono) sockets on the rear panel. To make connection to another amplifier easier, there is another pair of sockets which can patch the input signal through to another amplifier. This is especially useful if the OBH-21SE is used in series with the tape loop of a pre-amp or integrated amp. It is suitable for any line level analogue source.

In common with all electrical appliances, the OBH-21SE requires a power source. A custom stand-alone Creek OBH-Uni power supply is provided that must be connected to the unit via the DC inlet on the rear panel. The mains power supply and connector plug will vary, depending on country of use. Inside the OBH-21, custom circuitry is used to convert the power supply from a single, positive rail, into a split positive and negative supply and ghosted ground. Split-rail power supplies provide better Common Mode Rejection Ratio (CMMR) which will improve the sound quality by increasing interference suppression and allow for DC signal coupling on the SE version.

The OBH-21SE uses two instrument grade LM 7171 op-amp circuits and is DC coupled from input to output, for better sound quality. It uses a DC servo loop to eliminate any trace of DC from the output and give unrestricted output down to les than 1 Hz.

The OBH-21SE can also be used in conjunction with other Creek OBH series products, such as Phono pre-amplifiers or the OBH-22 passive pre-amplifier. Furthermore, it can also function with a stand-alone pre-amplifier or integrated amplifier, connected in the tape loop.

The OBH-21SE is a higher grade version of the standard OBH-21. Higher grade components and additional circuitry are used to produce a better performance. The main differences between the 21 and SE are as follows:-

Volume potentiometer type:

  • OBH21 is fitted with a 16mm carbon film pot.
  • OBH21SE is fitted with a 27mm plastic film pot.

Amplifier circuitry:

  • The OBH21 uses 2 x NE 5532.
  • OBH21SE uses 2 x LM 7171.

Signal coupling:

  • OBH-21 is AC coupled using audio grade caps.
  • OBH-21SE is DC coupled and offset voltages are controlled by a custom DC servo circuit.

Input socket type:

  • OBH-21, Nickel pressed metal.
  • OBH-21SE, Gold pressed metal.

Specification

Output Power>20mW
Suitable Headphone Impedance Range30 Ohms to 300 Ohms
Higher impedance headphones will work but the output level will be reduced proportionally.
Frequency Response10Hz to 50kHz +/- 1dB
Total Harmonic Distortion<0.01% @ 1kHz
Signal To Noise Ratio>70dB
Power Supply RequirementCreek UBH-Uni, (24V DC, 15W)
Power Consumption<3Watts in operation, 
< 1 W in standby
Weight3kg

Write Your Own Review

You're reviewing: Creek OBH-21SE Headphone Pre Amp

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars
Price
Value
Quality

Address

Origin Live Ltd. Unit 5, 362B Spring Road Sholing, Southampton SO19 2PB, UK